How to Adjust E-Bike Suspension for Rider Weight and Terrain
The key to adjusting e-bike suspension is to set the appropriate sag based on rider weight, total load, and riding terrain, then adjust preload, air pressure, or rebound damping according to the suspension system's available features.
Not all electric bikes use the same suspension setup. Some have adjustable front forks, others feature both front and rear suspension, and certain air forks offer independent rebound adjustment. Before making any adjustments, it's important to identify whether your bike uses coil or air suspension and which settings are actually adjustable.
A practical suspension setup follows a clear sequence: identify the suspension type and load limits, measure sag, adjust preload or air pressure, check rebound behavior, and verify the settings with a test ride.

What Are Preload, Sag, and Rebound in E-Bike Suspension?
An e-bike suspension system consists primarily of spring elements and damping mechanisms. Coil springs or compressed air support the load and store energy as the suspension compresses, while the damping system controls compression and rebound by dissipating energy. Together, these components help maintain ride comfort, tire contact, and bike stability. These components work together to maintain comfort, tire contact, and bike stability.
Before making any e-bike suspension adjustments, it's important to understand four common settings.
Preload
Preload refers to the initial compression applied to a spring before the suspension supports the rider's weight.
On coil-sprung forks equipped with a preload adjuster, increasing preload generally reduces static sag when the rider gets on the bike, making the fork feel more supportive at the beginning of its travel. Reducing preload may increase sag.
However, preload does not change the spring rate of a linear coil spring. For riders whose weight falls well outside the spring's intended range, increasing preload cannot replace a properly rated spring. The preload adjuster should never be tightened beyond its specified limit.
Sag
Sag is the amount of suspension travel used under the rider's static weight while seated or standing in a normal riding position. It is typically expressed as a percentage of total suspension travel.
Proper sag allows the suspension to retain enough travel for compression while also leaving room to extend. When a wheel passes over a dip or uneven surface, the suspension can extend downward to help the tire maintain contact with the ground.
Excessive sag often indicates insufficient spring support and may cause the suspension to sit too deep in its travel. Too little sag can reduce the suspension's initial responsiveness, making small bumps more noticeable.
Rebound
Rebound refers to the suspension returning to its original length after being compressed. Rebound damping controls how quickly this recovery occurs.
If rebound is too fast, the wheel or bike may bounce noticeably after passing over an obstacle. If rebound is too slow, the suspension may not fully extend between repeated impacts, causing it to settle progressively deeper into its travel.
Suspension systems equipped with rebound adjustment allow riders to change the rebound speed by adjusting the damping. However, not every e-bike fork or rear shock offers this feature.
Lockout
Lockout significantly restricts suspension movement to reduce unnecessary bouncing while pedaling on smooth surfaces.
Some lockout mechanisms still allow a limited amount of protective travel, meaning the suspension is not necessarily completely rigid. Riding over large bumps or obstacles with the suspension locked out may increase impact forces and stress on components. Always follow the manufacturer's instructions when using this feature.
Air vs. Coil Suspension
The main difference between coil suspension and air suspension is how each system provides spring support.
|
Feature |
Coil Suspension |
Air Suspension |
|
Spring element |
Metal coil spring |
Compressed air |
|
Common support adjustment |
Adjusting preload or replacing the spring |
Adjusting air chamber pressure |
|
Rider weight adjustment |
Depends on spring rate and preload range |
Air pressure adjustment within manufacturer limits |
|
Rebound adjustment |
Depends on the specific damping system |
Depends on the specific damping system |
|
Important consideration |
Preload cannot compensate for an incorrectly rated spring |
Requires a dedicated suspension shock pump |
Air suspension generally offers greater flexibility when adjusting spring support, but that does not mean every air suspension system includes independent rebound or compression damping adjustment. Available features should always be confirmed using the specific suspension model and its owner's manual.
How to Adjust E-Bike Suspension for Rider Weight
Rider weight is an important starting point for suspension setup, but adjustments must also account for backpacks, riding gear, and any additional cargo carried on the bike.
On the same electric bike with identical suspension settings, a heavier rider will generally produce more static sag. A lighter rider may not compress the spring enough, causing the suspension to feel harsh over smaller bumps.
Adding weight to a rear rack can also change how the load is distributed between the front and rear wheels. On a full-suspension electric bike, additional rear cargo often increases rear shock compression, although the actual effect depends on cargo placement, frame design, and riding position.
For this reason, suspension adjustments should begin with an assessment of actual riding conditions and a sag measurement rather than selecting a universal adjustment setting based on body weight alone.
Step 1: Check Rider Weight and Total Load
Before adjusting the suspension, record the following information:
- Rider weight, including a helmet, shoes, and other riding gear.
- Backpacks, panniers, and any additional cargo carried on the bike.
- Cargo placement on the front and rear racks, along with each rack's weight limit.
- The maximum load capacity specified by the bike manufacturer.
- Any separate load, air pressure, or spring limitations for the front fork and rear shock.
It's important to distinguish the bike's overall load capacity from the load limits of individual suspension components. A bike's stated maximum load is not necessarily the maximum load permitted for its fork or rear shock. It also does not mean that suspension adjustments can deliver identical performance under every loading condition.
Step 2: Measure Suspension Sag
Before measuring sag, check that the bike has no obvious mechanical problems and confirm the suspension's travel and correct measurement points. Prepare a ruler or measuring tape, use the suspension's travel indicator O-ring if available, and ask someone to help keep the bike stable.
Follow these steps:
- Set the suspension lockout or compression damping adjustment, if available, to the measurement position specified by the manufacturer. This usually involves disengaging the lockout.
- With the suspension fully extended and no rider weight applied, slide the travel indicator O-ring toward the dust seal.
- Put on your normal riding gear and get onto the bike in your usual riding position. Keep your feet on the pedals as much as possible while another person stabilizes the bike.
- Gently compress and release the suspension, allowing it to settle under normal riding weight.
- Maintain a natural riding position without deliberately leaning forward or backward.
- Carefully get off the bike without causing additional suspension compression, then measure the distance between the O-ring and its original position.
For a suspension fork, sag percentage can be calculated using the fork's effective travel:
Sag (%) = Sag Distance ÷ Total Suspension Travel × 100%
Target sag varies between suspension forks and rear shocks. As a general starting reference, some short-travel forks use approximately 10%–20% sag, while certain longer-travel forks use around 20%–30%. Rear shocks commonly use approximately 25%–30%. These ranges are not substitutes for the suspension manufacturer's instructions. If specific target values are provided, always follow the manufacturer's recommendations.
For rear suspension, sag should generally be calculated using the shock's effective stroke rather than rear wheel travel. Because full-suspension frame linkages can produce different amounts of wheel movement and shock compression, these measurements are not interchangeable.
If the suspension does not have a travel indicator O-ring or its effective travel cannot be confirmed, use a measurement method approved by the manufacturer. Avoid tools that could scratch the shock shaft or damage the seals.
Step 3: Adjust Preload or Air Pressure
After taking the initial sag measurement, make adjustments according to the suspension type.
For coil-sprung forks:
If the fork has a preload adjustment feature, gradually adjust it based on the measured sag and the direction specified by the manufacturer.
If static sag is excessive, preload may be increased within the permitted range. If sag is noticeably too low, reducing preload may help.
Measure sag again after each adjustment rather than relying solely on how the fork feels when pushed down by hand.
If the preload adjuster reaches its permitted limit and sag is still outside the manufacturer’s recommended range, the spring rate may not match the rider's weight. Consult a qualified bike technician to determine whether a different spring can be installed.
For air suspension:
Spring support in an air suspension system is primarily adjusted through air chamber pressure. Generally, increasing air pressure reduces static sag, while lowering pressure may increase it.
Use a dedicated suspension shock pump with a pressure gauge, and follow the suspension manufacturer's minimum and maximum pressure limits and inflation or deflation procedures.
Some air suspension systems require the suspension to be gently compressed after pressure changes to equalize air pressure between internal chambers before sag is measured again. The correct procedure depends on the suspension's internal design.
Do not substitute a regular tire pump for a dedicated suspension shock pump, and never apply an e-bike tire's recommended PSI directly to an air fork or rear shock.
Once spring support is set, begin with a low-speed test ride. If the suspension also supports rebound adjustment, set the rebound speed according to the instructions for that specific model.

How to Adjust Suspension for Different Terrain
Different surfaces place different demands on suspension, but the goal is not to readjust every setting whenever the terrain changes. Start with a baseline setup that matches rider weight, then make adjustments to address specific performance issues.
The same suspension system may feel smooth on paved roads but struggle to recover between repeated impacts on gravel. A setup that feels comfortable over a speed bump at low speed may not provide enough support during larger impacts.
Paved Roads
On smooth surfaces with relatively few impacts, suspension primarily handles cracks, pavement joints, and occasional small obstacles.
If the bike has a fork lockout, it may be used on smooth roads where the manufacturer permits it to reduce unnecessary suspension movement while pedaling.
However, everyday roads are not perfectly smooth. Before riding over potholes, speed bumps, or significantly damaged pavement, disengage the lockout according to the manual. Lockout should not be treated as a setting that must remain engaged at all times.
If the fork continuously transmits noticeable vibrations on ordinary roads, check tire pressure, lockout position, and sag before assuming that spring support needs to be reduced.
Gravel and Uneven Paths
On gravel and uneven surfaces, suspension needs to absorb repeated small impacts while helping the tires follow changes in the terrain.
If fork support is too firm or initial sag is insufficient, frequent vibrations may travel through the handlebars, and the front tire may have more difficulty maintaining consistent contact with rough surfaces.
Conversely, excessive sag reduces the available compression travel, making the suspension more likely to bottom out when encountering deeper bumps or holes.
In these situations, first confirm that the fork is not locked out, then check whether tire pressure, load, and sag are appropriate. Avoid continually reducing air pressure or spring support simply to achieve a softer feel.
For fat tire electric bikes, tire cushioning also needs to be considered. Wider tires can absorb some smaller impacts, but excessively low tire pressure may increase the risk of tire and rim damage. Tire cushioning is not a substitute for proper suspension setup.
Repeated Bumps and Rough Terrain
Repeated bumps are more likely to reveal problems with rebound settings.
When rebound damping is too strong and recovery is too slow, the suspension may not extend far enough before the next impact. As the bike travels over consecutive obstacles, the suspension can settle progressively deeper into its travel. This is commonly called packing down.
If rebound damping is insufficient, the suspension may extend too quickly after compression, causing noticeable wheel or bike bounce.
On models with adjustable rebound damping, make small adjustments according to the manufacturer's markings only after establishing the baseline sag setting.
Signs Your E-Bike Suspension Needs Adjustment
Suspension problems can be identified not only through static measurements but also by observing how the bike behaves during a ride.
|
Riding Symptom |
Possible Cause |
What to Check First |
|
Frequent bottoming out over larger bumps |
Excessive sag, insufficient spring support, or too much load |
Total load, preload, air pressure |
|
Harsh feel over small bumps |
Insufficient sag, engaged lockout, or mechanical resistance |
Lockout position, sag, fork movement |
|
Suspension sits progressively lower over repeated bumps |
Excessive rebound damping |
Rebound setting, if adjustable |
|
Noticeable bouncing after obstacles |
Rebound too fast or other incorrect settings |
Rebound, tire condition |
|
Rear of the bike sags significantly when carrying cargo |
Increased rear load |
Rear shock sag, cargo distribution |
|
Fork movement feels rough or produces unusual noises |
Problems with seals, bushings, or other mechanical components |
Suspension condition and professional inspection |
Suspension Too Soft
Suspension that is too soft often shows signs of frequent bottoming out, excessive front-end dive under braking, or significant rear-end sag on full-suspension bikes, which can affect handling and stability. These symptoms are commonly associated with insufficient spring support, excessive sag, or overloading, but tire pressure and possible suspension mechanical problems should also be checked.
Suspension Too Stiff
When suspension is too stiff, small vibrations may travel directly through the handlebars and frame, while the suspension may not use enough of its available travel, reducing the wheel's ability to follow uneven terrain. In addition to excessive preload or air pressure, check for overinflated tires, an engaged lockout, suspension binding, or other mechanical problems.

Mokwheel Suspension Adjustment by Model
Mokwheel models differ in suspension design and available adjustment features, so the same preload, air pressure, or rebound settings cannot be applied across every model. Before making adjustments, identify the type of front fork and rear shock, then choose the appropriate adjustment method based on rider weight, actual load, and terrain.
|
Mokwheel Model |
Suspension Configuration |
Max Load Capacity |
Key Adjustment Considerations |
|
Basalt 2.0 |
110mm adjustable front fork with lockout |
450 lbs |
Confirm available adjustments, check sag, and use lockout correctly |
|
Tarmac |
80mm air fork with lockout and rebound adjustment |
350 lbs |
Air pressure, sag, rebound speed |
|
Obsidian 2.0 |
130mm adjustable front fork, DNM rear shock |
560 lbs |
Check front and rear sag separately; adjust rear shock air pressure according to the manual |
|
Obsidian ST 2.0 |
130mm adjustable front fork with lockout, DNM 50mm air rear shock with 120mm of rear-wheel travel |
560 lbs |
Front fork lockout; rear shock air pressure and sag |
|
Onyx |
135mm adjustable front fork, DNM rear shock |
560 lbs |
Front fork lockout; rear shock air pressure and sag; load distribution |
For the Basalt 2.0, first confirm which adjustments the front fork supports, then check sag based on rider weight. The Tarmac features an air fork that allows spring support to be adjusted through air pressure within the specified range. Its rebound setting can also be fine-tuned based on how the fork recovers during riding. Because these models use different suspension designs, the same adjustment method should not be applied to both.
Basalt-2-0
For the full-suspension Obsidian 2.0, Obsidian ST 2.0, and Onyx, front and rear sag should be checked separately. When rider weight or rear cargo load changes, reassess rear shock sag to help prevent frequent bottoming out caused by insufficient support.
Obsidian 2.0 Ebike
Specific air pressure limits, preload adjustment ranges, and rebound settings should always be based on the suspension components installed on the bike and their corresponding manuals. Even models with identical suspension travel or maximum load capacities should not automatically use the same adjustment values.
Test Ride and Suspension Safety Checklist
Suspension adjustment is not a one-time process. Even when static sag is within an appropriate range, a test ride is necessary to confirm how the bike performs under different impacts.
Use a consistent test route and change only one setting at a time so you can identify which adjustment affects the bike's behavior.
Step 1: Check the Bike Before Riding
Before the test ride, inspect the front fork and rear shock for visible oil leaks, excessive play, damage, or loose components.
Confirm that the front and rear wheels, brakes, and handlebars are functioning properly. Check tire pressure and make sure all suspension adjusters are within their permitted ranges.
For air suspension, also confirm that the air valve caps are properly installed and the suspension can maintain air pressure.
Step 2: Record Initial Settings
Record rider weight, riding gear and cargo weight, tire pressure, and the current suspension settings.
For air suspension, record the actual air pressure. If the suspension has adjustable rebound damping, record its setting relative to the reference position specified by the manufacturer.
Keep tire pressure, test route, and riding conditions as consistent as possible to make comparisons between adjustments more accurate.
Step 3: Test at Low Speed
Choose a familiar, dry route with good visibility and little or no traffic for the initial test ride. Start at a low speed.
First, observe how the bike behaves on smooth pavement. Then gradually ride over minor surface changes and small bumps to check whether the suspension compresses and recovers smoothly.
Do not test suspension settings by immediately attempting jumps, large drops, or high-speed impacts. Never continue testing if obvious mechanical problems remain unresolved.
Step 4: Change One Setting at a Time
If further adjustment is needed, first identify the setting most likely responsible for the problem.
For suspension with adjustable rebound damping, make gradual changes within the manufacturer's permitted range and repeat the same test section after each adjustment.
Avoid changing air pressure, rebound, and tire pressure at the same time. Otherwise, it becomes difficult to determine which change actually improved the ride.
Step 5: Recheck and Maintain
After the test ride, inspect the fork, rear shock, and adjustment mechanisms for new oil leaks, unusual noises, or abnormal wear.
Use a soft, clean cloth to remove dirt from exposed suspension sliding surfaces and around the dust seals. Avoid directing high-pressure water at suspension seals.
If the suspension cannot maintain air pressure, develops noticeable play, or does not move normally, stop riding and have it inspected by a qualified bike technician.
Get the Right Suspension Setup for Your Ride
Proper suspension setup is not about making your bike as soft or stiff as possible. It's about maintaining the right balance of support, impact absorption, and recovery for your actual load and riding terrain. Starting with sag measurements and fine-tuning only the adjustments supported by your bike is more reliable than repeatedly turning adjustment knobs based on feel alone.
🚴 Explore Mokwheel electric bikes to learn more about the suspension configurations and riding characteristics of different models.